Auto Body: Dent & Rust Repair – 1 of 6

More info: www.metacog.com

acura, audi, Autobody, automobile, bmw, bondo, buick, cadillac, car, Cars, chevrolet, chevy, chrysler, ding, diy, dodge, Ford, gm, honda, hyundai, infiniti, isuzu, jaguar, jeep, job, kia, lexus, lincoln, mazda, mercedes, mercury, mitsubishi, nick, nissan, oldsmobile, paint, Painting, pontiac, prep, primer, sanding, saturn, scion, scratch, subaru, suv, toyota, truck, van, vehicle, volkswagen, volvo

Print article

This entry was posted by admin on September 2, 2010 at 5:38 pm, and is filed under auto body. Follow any responses to this post through RSS 2.0. You can leave a response or trackback from your own site.

Related Posts
Comments (25)

#1 written by thebibleisfiction
about 2 years ago

Reply Quote

thank you for uploading this, 5 stars very professional.
#2 written by interbug
about 2 years ago

Reply Quote

just what I need
#3 written by TheBlueToyota
about 2 years ago

Reply Quote

i have a question. i have a 20 year old toyota with large holes in the roker panels from rust. since this is a structural part of the car (for jacking) i cannot fill it with auto body putty. what should i do.
#4 written by funnyskater3
about 2 years ago

Reply Quote

his voice….its just so flat and borrrrrrrring… really good info though makes me want to but a junker car even more
#5 written by bender2o
about 2 years ago

Reply Quote

its a bodyshop job, they’d have to cut the rusted piece out, weld a new piece in, sand it down to fit and spray it to blend it in, its the only real way to get rid of cancerous rust
#6 written by TheBlueToyota
about 2 years ago

Reply Quote

is it possible if i just did it without reinforcing the roker panel because i think im good enough to do this.
#7 written by bender2o
about 2 years ago

Reply Quote

im sure if you got the same thickness metal or a little thicker and welded it in properly, aslong as the welds are stong, it should hold fine, but if i were you i’d send a quick email to a bodyshop and just ask there opinion aswell, it would be fine in my opinion though.
#8 written by TheBlueToyota
about 2 years ago

Reply Quote

thank you. im 13 and love to fix things and this is a 20 year old car so i just want to use it as a pratice car so its ok if i fuck up.
#9 written by drjim86
about 2 years ago

Reply Quote

I like these videos because they are good diy without using a lot of expensive equipment. Obviously not meant to restore a classic car but would help freshen up a daily driver that wouldn’t justify a $3000 body job.
#10 written by jaggajatt08
about 2 years ago

Reply Quote

i like his hair
#11 written by obcaraudio
about 2 years ago

Reply Quote

lol from 0:20 to 0:41, it looks like there is a real pistol being pointed at his head
#12 written by 50jofa
about 2 years ago

Reply Quote

the rocker is not just structure for jacking but also structure or the entire vehicle.. the rocker will need to be cut out “at proper cut points” and a new rocker properly weldied back in. in must be strong but not stronger then ment to be from factory
#13 written by evanellakb
about 2 years ago

Reply Quote

hahaha
#14 written by tomhotrod87
about 2 years ago

Reply Quote

anybody actually going to follow things get a better mask your lungs will last longer
#15 written by YouSpamTard
about 2 years ago

Reply Quote

Its ok to make rockers stronger. Not frame rails, but rockers are OK. Cars are made with whats called impact zones, but the passenger compartment is not made to absorb energy. Well kind of it is, like windshield posts from a front end wreck, but all in all, that part of the car, the passenger compartment is not made to give way. Its a gray area. If a B pillar is right next to a persons shoulder, is it better to have it give so less energy is passed into the compartment, or better ridged.
#16 written by MadSmokerBBQ
about 1 year ago

Reply Quote

oh that’s hilarious!
#17 written by MadSmokerBBQ
about 1 year ago

Reply Quote

the cheapo Harbor Freight respirator is $20 and a thousand times better than dust masks – breathes easy, doesn’t fog the goggles and
has replaceable filters. When I started using this I quit blowing rusty mud buggars after grinding.
#18 written by bbokainen
about 1 year ago

Reply Quote

wow, that looks nothing like “a real pistol” why are you such a dumb bitch
#19 written by Killiiminati
about 1 year ago

Reply Quote

also when you work outside?
#20 written by tomhotrod87
about 1 year ago

Reply Quote

yes even outside i have a Friend in need of a double lung transplant, and i dont think you want that. its better to be safe then dead
#21 written by vmodrak1
about 1 year ago

Reply Quote

Mullets rule!!!!!!!!!!!!
#22 written by FistsOfTime
about 1 year ago

Reply Quote

25 seconds in and this video is already amazing. i hope this video was shot this year.
#23 written by FistsOfTime
about 1 year ago

Reply Quote

8:06
#24 written by 95steveexplorer
about 1 year ago

Reply Quote

mullet!!
#25 written by kamchuka
about 1 year ago

Reply Quote

mullet….check, fuckin bitchin mustache….check…..awesomeness….check….begin